The following manual is applicable for 32bit Ubuntu 6.10 (Edgy Eft) and 7.04 (Feisty Fawn) and Verizon Motorola v3 EV-DO enabled phone connected via USB cable as well as number of other EV-DO cards like PC5750.
Make sure your device is activated by service provider and if possible test on other OS to which you may have software and drivers.
Open terminal window and type:
sudo -i
and enter your password.
Now all commands typed in this window will be executed with root privileges.
In terminal type:
apt-get update
apt-get upgradeapt-get install wvdial
Before you insert the Card or connect USB cable open terminal window and type:
cat /proc/bus/usb/devices > devices
Insert your data card or plug in USB cable and wait for a few seconds before continuing.
In terminal type:
dmesg
You will get output with some device info like this :
[17186692.460000] usb 3-1: configuration #1 chosen from 2 choices[17186692.460000] cdc_acm 3-1:1.0: ttyACM0: USB ACM device[17186708.176000] usb 3-1: USB disconnect, address 4
[17186714.588000] usb 3-1: new full speed USB device using uhci_hcd and address
At the end of this output you will find your device witch will be represented like this: ttyACM0 or ttyUSB or similar , make note of it you will need it later.
Now type in terminal:
cat /proc/bus/usb/devices | grep Vendor
Output will be similar to:
< P: Vendor=1234 ProdID=5678 Rev= 0.00
Make note of lines: Vendor=1234 , ProdID=5678
Now in teminal type following code Replacing values 1234 and 5678 with your own output from previously noted lines ::
modprobe usbserial vendor=0x1234 product=0x5678
Now you will edit wvdial config file by first typing in terminal :
sudo gedit /etc/wvdial.conf
In new opened window replace all text with following :
[Dialer Defaults]
Stupid Mode = on
Modem = /dev/ttyACM0
Baud = 921600
Init = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Phone = #777
Username = ??????????@vzw3g.com
Password = vzw
Init1 = ATZISDN = 0
Modem Type = Analog Modem
Auto Reconnect = on
Carrier Check = no
[Dialer shh]
Init3 = ATM0
[Dialer pulse]
Dial Command = ATDP
In the line “Modem =” replace ttyACM0 with value you noted from output of dmesg command.
In the line ” Username = ” put your phone number followed by your providers domain, for Verizon it is area code, your phone number and domain, in this format: 9178889999@vzw3g.com for Sprint it will be 9178889999@sprintpcs.com, for AT&T / Cingular WAP@CINGULARGPRS.COM, for Alltel 9178889999@alltel.net and so on, further post have config’s posted for other providers.
In line ” password = ” in case of Verizon put: “vzw” for Cingular: “cingular1″ and so on, make sure to check with your provider as username and/or password may differ for other regions and countries.
If you are Cingular/AT&T subscriber and after completing whole guide you have problem with dropping connection you have to add another int line in wvdial script which is posted here http://ubuntuforums.org/showthread.php?t=343989&page=3
If you need any specific info regarding your domain or password please contact your cellular provider.
The last thing you need to configure is wvdial line checking, by disabling LCP echo checking witch is not supported by most of providers.
Open terminal and type:
sudo gedit /etc/ppp/peers/wvdial
And insert aditionally those lines:
lcp-echo-failure 0
lcp-echo-interval 0
Make sure your ethernet jack is unplugged and wifi radio switch is turned off.
Now you can start connection by typing in terminal :
wvdial
Another thing i have been suggested is automating the connection process.
To do so in Gnome go to :
System > Preferences > Sessions next, click on the tab labeled, “Startup Programs” then click the “Add” button.
In the Startup Command field, enter “wvdial” and then click “OK”.Then restart your system.
Now make sure your EV-DO card is inserted before you boot it up, it will initiate the connection process automatically in the background connecting you to internet the second you log in.
The manual is kindly provided by Mach1US.
Recent Ideas